Má někdo zkušenost jestli je nějakej rozdíl (karburátory keihin CV), když
1. je menší VT a šroub bohatosti např. 3,5 otáčky
2. nebo VT větší a šroub bohatosti 2,5 otáčky
Volnoběh je nastavenej pořád stejně, jde mi jen o to, jestli jsou nějaký rozdíly když je různej poměr VT a šroub bohatosti - tzn. jestli je lepší varianta 1,2 nebo je to jedno.
No a za druhý - kolega vyprávěl že součet trysek by měl být pořád stejnej - tzn. když dám větší volnoběžnou, měl bych menší hlavní tak, aby byl součet stejnej jako před výměnou, měl pravdu nebo houpal? Ono totiž i ten šroub bohatosti např. u mý motorky co otáčka to o jeden krok větší/menší volnoběžná.
1 reakcí na tento příspěvek Složení volnoběžné směsi + součet VT a HT - keihin
Greg Johnson wrote:
> I have installed one of your 1.0 jet kits on my R6 and I am coming to the final parts of tuning it.
> It runs well and passes most of the tests as provided on your tuning guide. It does, however, appear to be lean low down, as there is a "hole" when cracking the throttle wide open at below 2500rpm and at high rpm/part throttle, it shows some surging. I have though set the fuel screws, so that it idles correctly and returns to the correct rpm, when the idle is set below 1000rpm and the throttle is blipped.
> To fix the lean patch, is it better to go the next step up in pilot jets, rather than adjust the fuel screw?
> Will upsizing the pilot jet, require re-adjustment of the fuel screw and thus negating some of or all of the gains made by the larger pilot jet?
> Thanks,
> Greg J
Answer:
Greg - Good diagnosis on the pilot jet size -
As far as the pilot... Look at it this way...
There are 4 outlet holes for the pilot mixture. ~3-4 at the butterfly and one "downstream" of that (for 75% of the idle mixture).
1 hole is controlled by the mixture screw and with the other 3 or 4, max flow is limited by the size of the pilot jet.
At idle, 1 hole (metered by the fuel screw) and 1 un metered hole are open.
At cruise, when the "butterfly" is just "cracked", all 3-4 unmetered holes + the 1 metered one are uncovered -
So.....
At cruise, you get those 3 unmetered holes + the metered hole... So, at least 75% of the fuel delivered at cruise is limited by the size of the pilot jet.
At idle, you get 100% of the trimmed 1 hole + a butterfly valve-trimmed amount of the other 3-4 metered holes.
Rule of thumb....
If you go 1 size larger or smaller on the size of the pilot jet, you will change the fuel screw ~1.5x richer or leaner to retain the original idle mixture -
Example:
You have a #40 pilot jet installed (with the proper main, needle height and fuel level already done) and to get best idle, you are 4.0 turns out (from lightly bottomed out).
(Using another "rule of thumb", if you have the correct pilot jet, the fuel screw will end up at between 1.5x and 3.0x when set for best idle.)
Cruise seems lean....
So, I'd expect that I could richen the cruise with 1 size larger (42) pilot jet (size of pj is 75% of cruise mixture) and the "trim" the fuel screw "in" for best mixture for best idle (size of pilot is 25% of idle mixture).
To go back to ~ the same idle mixture, after going from 40 pj/4.0x to the 42........ try 2.5x
40 pj / 4.0x = our reference idle mixture
42 pj / 2.5x = ~ same idle mixture
38 pj /5.5x = ~ same idle mixture (this is a "stretch - after 4.5x, not much changes)
Marc
Téma | Autor | Odp. | Posl. příspěvek |
---|---|---|---|
Bridgestone Batlax A41 Adventure, r... Ostatní cestovní | greg600 | 10 | 24.2.2024 v 19:31 NUTELIER |
Točí semi gripy Ostatní cestovní | bommbay | 14 | 4.2.2024 v 19:04 kalous72 |
vyplatí se 125ccm Ostatní cestovní | obcasjuli | 23 | 20.10.2023 v 18:46 dva_hrnce |
grossglockner [1, 2] Ostatní cestovní | Zbyněc | 38 | 12.9.2023 v 22:29 TomasNBK |
Bulharsko, Řecko 2023 Ostatní cestovní | Milan1963 | 15 | 11.9.2023 v 15:15 Milan1963 |